|
2010 TURBOMECA USA
ENGINE MAINTENANCE TRAINING SCHEDULE | Class | Date Class Begins | Duration | Arriel 1 (All Variants)
(Initial Engine Maintenance) | January 25 | 5 Days (Concludes January 29) | | March 8 | 5 Days (Concludes March 12) | | April 26 | 5 Days (Concludes April 30) | | June 21 | 5 Days (Concludes June 25) | | August 23 | 5 Days (Concludes August 27) | | Novemeber 15 | 5 Days (Concludes November 19) | | | | | Arriel 1E2
(Initial Engine Maintenance) | March 1 | 5 Days (Concludes March 5) | | June 28 | 5 Days (Concludes July 2) | | August 30 | 5 Days (Concludes September 4) | | Novemeber 15 | 5 Days (Concludes November 19) | | | | | Arriel 2B/2B1
(Initial Engine Maintenance) | February 8 | 5 Days (Concludes February 12) | | February 22 | 5 Days (Concludes February 26) | | March 29 | 5 Days (Concludes April 2) | | May 17 | 5 Days (Concludes May 21 ) | | July 5 | 5 Days (Concludes July 9) | | August 2 | 5 Days (Concludes August 6) | | October 18 | 5 Days (Concludes October 22) | | November 1 | 5 Days (Concludes November 5) | | December 13 | 5 days (Concludes December 17) | | | | | Arriel 2S1/2S2
(Initial Engine Maintenance) | March 15 | 5 Days (Concludes March 19) | | April 12 | 5 Days (Concludes April 16) | | June 7 | 5 Days (Concludes June 11) | | August 9 | 5 Days (Concludes August 13) | | October 4 | 5 Days (Concludes October 8) | | December 6 | 5 Days (Concludes December 10) | | | | | Arrius 2F
(Initial Engine Maintenance) | February 1 | 5 Days (Concludes February 5) | | April 19 | 5 Days (Concludes April 23) | | July 26 | 5 Days (Concludes July 30) | | September 27 | 5 Days (Concludes October 1) | | | | | Arrius 2B1/2B2
(Initial Engine Maintenance) | February 8 | 5 Days (Concludes February 12) | | March 29 | 5 Days (Concludes April 2) | | July 5 | 5 Days (Concludes July 9) | | | | | | | | |
Special Request Classes
The following classes are scheduled by request and may require substantial advance notice. | Engine Type | Class Type | | Arriel 2C or 2C1 or 2C2 | Initial Engine Maintenance | | Arrius 1A or 1A1 or 2K1 | Initial Engine Maintenance | | Makila 1A1 or 2A | Initial Engine Maintenance | | Older Generation Engines | Initial Engine Maintenance | | All Models | Refresher or Familiarization or Troubleshooting | | All Models | Initial or 2nd Line Engine Maintenance Refresher (Prerequisite of same level course) | | All Models | 2nd Line Maintenance Only (Initial prerequisite) | | Offsite Classes (at Customer’s Location) | | Any Class conducted per EASA 147 | | Any Class conducted under Transport Canada requirements | | Any Class requested in a language other than English (cost of Translator is additional) |
General All classes are conducted by Turbomeca USA, Inc., Grand Prairie, Texas.
All initial classes are in English unless otherwise specified. Class size is limited to 6 students minimum and 10 maximum. 2nd Line Maintenance classes are limited to 6 persons maximum.
All information is subject to change without notice.
Students must meet the following Prerequisites:
For Initial (O-level) maintenance courses, participants must be aeronautical maintenance technicians with at least one year's experience on gas turbine engines.
Participants must understand and speak the language in which the course that they are enrolling in will be given. If this is not the case, TM calls on the services of an interpreter. Definition of Class Type Initial Maintenance Scheduled, Preventive or Corrective Maintenance that is described in the Engine Maintenance Manual, Service Letters, Service Bulletins or Technical Instructions and that is to be performed with the engine installed on the helicopter. 2nd Line Maintenance Maintenance described in the Engine Maintenance Manual that is to be performed with the engine removed from the helicopter. Off Site Classes These classes are to be conducted away from Turbomeca USA at the customer’s location. Scheduling of the dates, times, locations, and class size for these classes will be requested well in advance to allow Turbomeca USA to fit them into the existing schedule.
Exceptions:
New helicopter purchases include initial training for one (1) student per factory-installed engine within one (1) year of delivery date.
Training designated by a TMUSA contract. Enrollment Information Enrollment to attend a class must be made in advance and a written confirmation from the Turbomeca USA Customer Training Department must be presented by the student upon arrival for class. Compliance with U.S. Government I.T.A.R. and T.A.A. regulations required for all students. For further information or enrollment, please contact the TMUSA Customer Training Department. Pre-enroll online via our website. http://www.turbomeca-usa.com Phone: 972-606-7600 or 800.662.6322 USA 800.553.6322 Canada
|
